- 您现在的位置：买卖IC网 > Sheet目录366 > TPS23757EVM (Texas Instruments)EVALUATION MODULE FOR TPS23757
TPS23757
SLVS948D – JULY 2009 – REVISED NOVEMBER 2013
www.ti.com
Option 1 ORing of a low voltage adapter (e.g., 24 V) is possible by connecting a resistor divider to PPD as in
Figure 30 . When 1.55 V ≤ V PPD ≤ 8.3 V, the hotswap MOSFET is enabled, APb is activated, and the class
feature is disabled. The hotswap current limit is unaffected, limiting the available power. For example, the
maximum input power from a 24 V adapter would be 9.3 W [(24 V – 0.6 V) × 0.4 A].
DEN
PPD
CLS
V SS
D A
APD
R PPD1
Adapter
Figure 30. Low-Voltage Option 1 ORing
Softstart
Converters require a softstart on the voltage error amplifier to prevent output overshoot on startup. Figure 31
shows a common implementation of a secondary-side softstart that works with the typical TLV431 error amplifier.
The softstart components consist of D SS , R SS , and C SS . They serve to control the output rate-of-rise by pulling
V CTL down as C SS charges through R OB , the optocoupler, and D SS . This has the added advantage that the
TLV431 output and C IZ are preset to the proper value as the output voltage reaches the regulated value,
preventing voltage overshoot due to the error amplifier recovery. The secondary-side error amplifier will not
become active until there is sufficient voltage on the secondary. The TPS23757 provides a primary-side softstart
which persists long enough (~4 ms) for secondary side voltage-loop softstart to take over. The primary-side
current-loop softstart controls the switching MOSFET peak current by applying a slowly rising ramp voltage to a
second PWM control input. The PWM is controlled by the lower of the softstart ramp or the CTL-derived current
demand. The actual output voltage rise time is usually much shorter than the internal softstart period. Initially the
internal softstart ramp limits the maximum current demand as a function of time. Either the current limit,
secondary-side softstart, or output regulation assume control of the PWM before the internal softstart period is
over. Figure 21 shows a smooth handoff between the primary and secondary-side softstart with minimal output
voltage overshoot.
From Regulated
Output Voltage
R SS
D SS
C SS
R OB
C IZ
R FBU
R FBL
TLV431
Figure 31. Error Amplifier Soft Start
30
Submit Documentation Feedback
Copyright ? 2009–2013, Texas Instruments Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
TPS62230EVM-370
EVAL MODULE FOR TPS62230-370
TRAVELCUBE
SURGE SUP 1OUT W/RJ11 DIRECTPLUG
TRAVELER100BT
SURGE SUP 2OUT W/RJ11 DIRECTPLUG
TRAVELER3USB
SURGE SUPP USB CHARGE TRAVEL SZ
TRAVELERC6
SURGE SUPPRESSOR 120/240V RJ11
TRAVELERC8
SURGE SUPPRESSOR 120/240V RJ11
TRAVELER
SURGE SUP 2OUT W/RJ11 DIRECTPLUG
TRK-MPC5604B
MPC5604B 144PIN REV 2.1
相关代理商/技术参数
TPS23757PW
功能描述:热插拔功率分布 Hi Eff PoE Inter & DC/DC Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS23757PWR
功能描述:热插拔功率分布 Hi Eff PoE Interface & DC/DC Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375D
功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375D
制造商:Texas Instruments 功能描述:POWER OVER ETHERNET ((NW))
TPS2375DG4
功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375DR
功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375DRG4
功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2375EVM
功能描述:电源管理IC开发工具 TPS2375 POE Powed Device Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V